Author: Site Editor Publish Time: 2026-02-02 Origin: Site
Pruning thick and large branches is an important and indispensable task in gardening. Whether it's fruit trees, ornamental trees, or large garden trees, proper pruning not only promotes healthy growth but also increases fruit yield and aesthetics. However, many gardening enthusiasts and professionals often face problems such as unsuitable tools, low efficiency, and even safety hazards when dealing with thick and large branches. Therefore, choosing efficient and durable pruning shears and mastering the correct pruning methods are crucial.
Pruning thick branches (3-10 cm in diameter) and large branches (over 10 cm in diameter) presents significant challenges compared to ordinary branches:
Ordinary garden shears or small manual pruning shears often cannot easily cut larger branches. Forcing the cut can easily damage the blades or break the handle.
For thick, large branches, using unsuitable pruning shears can require significant physical effort with each cut, resulting in low efficiency, especially during large-scale pruning.
Thick or large branches may spring back or slip during pruning, posing risks of pinching hands or falling and injuring people. Without protective measures or proper pruning techniques, the probability of accidents increases significantly.
Incorrect pruning methods can easily cause bark tearing or branch splitting, increasing the risk of bacterial infection and thus affecting tree growth and lifespan.
Therefore, pruning thick and large branches requires a combination of professional pruning shears and scientific operating methods to ensure efficiency, safety, and tree health.
When purchasing pruning shears, consumers should make a scientific selection based on branch thickness, intended use, and tool material. The following factors are key:
The blade design of pruning shears directly affects the pruning effect and user experience. Common blade types include:
Anvil type: The blade presses against a flat base, suitable for hardwoods and thick branches, but can easily crush branches; suitable for non-precise pruning.
Bypass type: Two blades are offset from each other, resulting in a clean cut; suitable for healthy branches and fine pruning.
Long-handled hydraulic type: Uses hydraulic pressure to increase force, suitable for large branches with a diameter exceeding 50 mm, reducing physical exertion.
High-efficiency pruning shears typically use high-quality alloy steel or carbon steel blades, heat-treated and rust-proofed, resulting in sharp and durable blades. The handles are often made of aluminum alloy or reinforced fiberglass, balancing lightweight and strength.
Long-handled pruning shears provide greater leverage, suitable for pruning thick branches; short-handled shears are flexible and suitable for fine work in small areas. Some professional pruning shears feature adjustable handles and non-slip grips, improving operating comfort and safety.
High-quality pruning shears allow for blade replacement or lubrication maintenance, resulting in a longer service life and reduced long-term costs. The detachable design also facilitates carrying and storage.
Pruning Shears Selection Guide
Blade Type | Applicable Branch Diameter | Advantages | Disadvantages | Typical Users |
Bypass | 1-5 cm | Clean cut, suitable for fine pruning | not suitable for thick hardwood branches | Home gardening, fruit tree pruning |
Anvil | 3-10 cm | Significantly increased force, suitable for thick branches | cut may crush branches | Garden maintenance, thick branch pruning |
Long-handled hydraulic | 5-10 cm and above | Labor-saving and efficient | High cost and weight | Professional gardening, public green space management |
Choosing the right pruning shears is only the first step; correct operating techniques can significantly improve efficiency and reduce safety risks.
For branches with larger diameters, the "three-section pruning method" is recommended:
First Section: Make a small cut slightly away from the base of the branch to reduce its weight.
Second Section: Cut the branch close to the trunk, avoiding tearing the bark.
Third Section: Trim any remaining branches to make a smooth cut, promoting healing.
This method is suitable for thick and large branches, especially fruit trees or large garden trees, reducing the risk of damage and cracking.
For high or large branches, use ladders or branch support ropes to secure the branches and prevent accidental falls. Long-handled hydraulic shears combined with stable supports can perform efficient pruning while ensuring safety.
Sharpen the blades: Clean promptly after use and apply rust-preventive oil.
Lubricate the shear shaft: Keep the shears opening and closing smoothly, extending their service life.
Check the handle and screws: Ensure the connection is secure to prevent loosening and injury during operation.
Choosing a reliable supplier is crucial when purchasing efficient pruning shears. A high-quality pruning shears supplier not only provides high-quality tools but also offers pre-sales and after-sales service, ensuring a positive consumer experience and long-term value.
A reputable supplier will provide material specifications, durability testing, and warranty services to ensure sharp blades, sturdy handles, and standard cutting results.
Suppliers should offer pruning shears with different blade types, handle lengths, and hydraulic extension options to meet diverse needs such as home gardening, orchard management, and public greening.
For landscaping companies or large orchards, a reputable pruning shears supplier can provide wholesale and customization services, including blade reinforcement, marking and lettering, and customized packaging.
Recommended pruning shears supplier contact information:
Email: tinafang@raykatool.com
Website: https://www.raykatool.com
Rayka pruning shears supplier offers a full range of high-efficiency pruning shears, covering both home gardening and professional landscaping. Wholesale and customization are supported, with reliable quality and comprehensive after-sales service.
Pruning thick and large branches is a challenging yet crucial gardening task. Choosing efficient pruning shears, employing scientific operating techniques, and regular maintenance are key factors in ensuring successful pruning. When purchasing pruning shears, consumers should comprehensively consider blade type, material, handle length, and supplier service quality. Furthermore, mastering the three-stage pruning method, using auxiliary support tools, and regularly maintaining the shears can significantly improve efficiency, ensure safety, and protect tree health.
Choosing a reliable pruning shears supplier, such as Rayka pruning shears supplier, not only provides high-quality tools but also enjoys professional pre-sales consultation and comprehensive after-sales service. Whether for home gardening or professional landscaping, efficient pruning shears are indispensable tools.
With Us 
